Gas Fireplace Pilot Won't Stay Lit? Here's What Might Be Wrong

By Daron | Your HVAC Guy — Abbotsford, BC

There's nothing quite like turning on your gas fireplace on a cold evening, only to discover it won't light.

Maybe the pilot lights while you're holding down the control knob but goes out the moment you let go. Or perhaps the pilot stays lit, but the main burner refuses to turn on.

Both are common problems, especially with older gas fireplaces.

I'm Daron, the owner of Your HVAC Guy in Abbotsford. I regularly diagnose and repair gas fireplaces throughout the Fraser Valley, and one thing I've learned is that a fireplace that won't light doesn't necessarily need an expensive repair.

Sometimes the problem comes down to a dirty pilot assembly or a relatively inexpensive component.

Here's what might be happening.

1. Your Thermocouple Might Be Failing

If your fireplace pilot lights but goes out as soon as you release the control knob, the thermocouple is one of the first things worth investigating.

A thermocouple is a small metal sensor positioned in the pilot flame.

When heated, it generates a tiny electrical signal that helps keep the gas valve open on fireplaces with this type of pilot system.

If the thermocouple isn't producing enough voltage, the gas valve may shut off the pilot as a safety precaution.

But here's something important.

Just because the pilot won't stay lit doesn't mean the thermocouple is bad.

I've seen perfectly good thermocouples replaced when the actual problem was a weak pilot flame that wasn't heating the sensor properly.

That's why testing matters.

2. The Pilot Assembly Could Be Dirty

This is one of the more common issues I encounter during fireplace service calls.

Over time, dust, lint and debris can collect around the pilot assembly.

Even a small restriction can affect the pilot flame.

Instead of a strong blue flame properly contacting the thermocouple, you might get a weak or poorly directed flame.

The thermocouple doesn't receive enough heat, and the gas valve shuts down.

During a service call, I'll inspect and clean the pilot assembly as needed, check the flame and verify that the safety components are operating correctly.

Sometimes that's all it takes to get a fireplace working again.

3. Your Thermopile Could Be Getting Weak

Most people have never heard of a thermopile, but it's an important component in many older gas fireplaces.

It looks similar to a thermocouple, only larger.

The thermopile uses the heat from the pilot flame to generate electricity, usually measured in millivolts.

On traditional millivolt fireplace systems, that electricity helps operate the main burner through the wall switch or thermostat.

A weak thermopile can cause several problems:

  • The pilot stays lit, but the main burner won't turn on.

  • The fireplace works intermittently.

  • The burner lights but shuts off unexpectedly.

A common mistake is replacing the gas valve when the real problem is insufficient electrical output from the thermopile.

Proper diagnosis includes measuring the output and determining whether the electrical signal is sufficient under operating conditions.

It's a relatively straightforward test for a qualified technician, and it can prevent unnecessary repairs.

4. The Gas Valve Could Be the Problem

Sometimes the thermocouple is working, the pilot flame is strong, and the fireplace still won't stay lit.

At that point, the gas valve becomes one of the components worth investigating.

Many fireplaces have a safety mechanism inside the gas valve that holds the pilot gas supply open only when the proper flame signal is present.

If that mechanism fails, the pilot may go out even when the thermocouple is producing sufficient voltage.

Gas valves can also develop problems that prevent the main burner from operating.

However, a gas valve is generally more expensive than a thermocouple or thermopile.

Before recommending replacement, I want to know that the valve is actually the problem.

Replacing parts without diagnosing the cause can get expensive quickly.

5. The Wall Switch or Remote Could Be Faulty

What if your pilot stays lit, but nothing happens when you turn on the fireplace?

Before assuming there's a major problem, check the simple things.

If you use a remote control, try replacing the batteries. Some fireplaces also have a battery-powered receiver that may need attention.

On older millivolt systems, the wall switch itself can become unreliable over time.

Because these systems operate on very low voltage, even a small amount of electrical resistance from a worn switch or poor connection can prevent the burner from operating.

The pilot may be perfectly fine.

A technician can test the switch circuit and electrical output to find the actual cause.

6. Venting Problems Can Also Cause Fireplace Shutdowns

Not every fireplace problem is electrical.

Depending on the type of fireplace, blocked venting, downdrafts or problems with a safety switch can cause the unit to shut down.

This is something I take seriously.

Your fireplace needs to vent combustion gases safely outside your home.

If there's a problem with the venting system, getting the fireplace to light again isn't the real solution.

The underlying issue needs to be identified and corrected.

If you notice unusual soot buildup, strong odours, abnormal flames or signs of heat damage, stop using the fireplace and have it inspected.

7. What Can You Check Yourself?

There are a few things homeowners can safely check before arranging a service call.

Check the remote batteries. If your fireplace uses a remote, replacing weak batteries is an easy place to start.

Check the wall switch. Make sure it's in the correct position and that a separate remote receiver hasn't been switched off.

Check the thermostat setting. If the fireplace is controlled by a thermostat, make sure it's actually calling for heat.

Look at the pilot flame. If your fireplace has a visible pilot, observe whether it's lit and whether the flame appears unusually small or unstable. Don't remove sealed glass panels to inspect it.

Review the lighting instructions. If your fireplace has a standing pilot and the manufacturer permits homeowner relighting, follow the instructions exactly. If the pilot repeatedly goes out, stop trying and have it inspected.

Don't attempt to adjust gas pressure, bypass safety controls or dismantle the pilot assembly.

Those repairs should be left to a qualified gas fitter.

8. Is It Worth Repairing an Older Gas Fireplace?

In many cases, absolutely.

I've worked on older fireplaces that were still in good overall condition but needed a thermocouple, thermopile or routine maintenance.

Those repairs can be considerably less expensive than replacing the entire fireplace.

However, there are situations where replacement makes more sense.

Heavy corrosion, damaged components, obsolete replacement parts or concerns about the condition of the venting system can change the recommendation.

I recently inspected an older fireplace that had extensive rust throughout the burner and pilot assembly. The equipment was in poor condition, and rather than recommend a series of repairs, I advised against using it and recommended replacement with further chimney evaluation.

That's the difference between getting something to light and making sure it's worth repairing safely.

My goal isn't simply to get the flame burning again. It's to make sure the fireplace operates properly and safely.

9. Does Your Gas Fireplace Need Annual Maintenance?

I recommend having gas fireplaces inspected and serviced annually, particularly if they're used regularly.

During a typical fireplace maintenance appointment, I may:

  • Inspect and clean the burner and pilot assembly.

  • Test the thermocouple and thermopile where fitted.

  • Inspect the gas valve and ignition system.

  • Check the condition of the venting system.

  • Inspect the logs and verify proper placement.

  • Clean the fireplace glass.

  • Check the condition of accessible seals and components.

  • Test operation and check for carbon monoxide.

The exact service depends on the fireplace and the manufacturer's requirements.

A properly maintained fireplace is more likely to operate reliably, and a routine inspection can identify problems before they result in a breakdown.

In some cases, FortisBC maintenance rebates may also be available for qualifying gas appliances and services.

Gas Fireplace Repair in Abbotsford and the Fraser Valley

I'm Daron, the owner of Your HVAC Guy.

I provide gas fireplace maintenance, diagnostics and repairs throughout Abbotsford, Mission, Aldergrove, Chilliwack and surrounding Fraser Valley communities.

As a licensed gas fitter, I believe in properly diagnosing equipment before recommending repairs.

Sometimes a fireplace that looks like it's finished simply needs a little attention. Other times, it's better to leave it off and discuss replacement options.

Either way, I'll explain what I find and give you a straightforward recommendation.

If your fireplace pilot won't stay lit, the burner isn't coming on, or something just doesn't seem right, I'm happy to help you figure it out.

Your HVAC Guy — Heating, Cooling & Gas Fireplace Service

Learn more about HVAC repairs

Get in touch with Your HVAC Guy

Safety note: If you smell natural gas, leave the building immediately. Avoid operating switches or electrical devices and contact FortisBC's emergency service or 911 from a safe location. If your carbon monoxide alarm sounds, evacuate and call emergency services.

Previous
Previous

Should You Repair or Replace Your Furnace? An Honest Guide for Fraser Valley Homeowners

Next
Next

BC Heat Pump Rebates in 2026: How Much Can Fraser Valley Homeowners Save?